The Foundation of Plumbing Skills for Bathtub Installation
The Foundation of Plumbing Skills for Bathtub Installation
Blog Article
Just how do you really feel in relation to How to Install a Bathtub?
Mounting a bath tub isn't precisely rocket science, yet it does call for solid plumbing, woodworking, and also occasionally, tiling abilities. Changing an old bath tub with a new one is also a reasonably tough project. If the old bathtub is conveniently accessible, the task can relocate immediately; if you have to open up a wall surface to eliminate the old tub as well as place the brand-new bathtub, the task is much harder. In either situation, the job is within a house handyman's skills, although you will certainly require a helper to vacate the old bathtub and embeded in the new one. Make certain you have qualified on your own for the work and are comfortable attempting it. As opposed to hiring a service provider to take over a halfway-completed job, it is far better to think about using one prior to you begin. Possibilities are you may require a specialist plumber to make tube links.
This article will aid you mount a brand-new tub in your shower room if you have currently gotten a new tub and don't require to transform the arrangement of your previous water supply pipes.
Your devices and also product list need to make up the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your installment, then the first thing you should do is detach the water supply. After doing so, turn on the taps to drain any water remaining in the system. The process of removing the existing taps can be fairly bothersome as a result of the limited accessibility that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly originate from the pipelines. When the supply pipes have actually been removed, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing compound.
Before carrying on to fit the new faucets, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, after that you will require a plastic adapter to prevent damages to the string. One end of the port fits on the plastic tail of the faucet and the various other end offers a link to the existent supply pipes.
If you require to fit a monobloc, after that you will need lowering couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin guaranteeing that the washers remain in area in between the faucet and also the sink. Protect the faucet in place with the supplier provided backnut. Once the faucet is securely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal tap connectors. The former type ought to be linked to the tap finishes initially, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Mounting the Bathtub
Making use of the two wood boards under its feet, place the bath tub in the required placement. The wooden boards are handy in evenly spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto four tiny points.
The following goal is to ensure that the tub is leveled all round. This can be achieved by examining the spirit level and also adjusting the feet on the bath tub up until the level checks out degree.
To install faucets, fit all-time low of the furthest versatile tap port to the ideal supply pipeline by making a compression sign up with; after that do the same for the various other faucet.
Turn on the water supply as well as examine all joints and new pipework for leaks and tighten them if needed. Fill up the bath tub as well as additionally examine the overflow electrical outlet as well as the typical outlet for leakages.
Ultimately, take care of the bath paneling as defined in the supplier's user's manual. Tiling and sealing around the bath tub must wait till the bath tub has actually been utilized a minimum of when as this will certainly settle it right into its final position.
Planning for the Setup
Firstly, the sustaining frame supplied with the bathroom needs to be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to see to it that if the tap features a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets system to prevent stress on the bath tub.
Fit the flexible tap ports to the bottom of the two taps using 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be suited its last setting.
Tiling Around the Bathtub
In the location where the bath meets the tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to crack a rigid seal, causing the water to permeate the wall in between the bath as well as the tiling, bring about complications with dampness and feasible leakages to the ceiling below.
You can select from a selection of coloured sealants to blend in your fixtures as well as installations. They are offered in tubes and cartridges, and also are capable of sealing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of soaked paper or soft rope. Keep in mind to constantly fill up the bath tub with water before securing, to enable the activity experienced when the tub is in use. The sealer can fracture relatively very early if you do not take into consideration this activity before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily available on the marketplace. It is suggested to fit the tiles using water-resistant or water resistant glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I have been very serious about Installing A Bathtub and I am assuming you liked my post. Sharing is nice. Helping people is fun. I love reading our article about How to Install a Bathtub.
Preserve your space; contact us. Report this page